• 0 800 357272
  • Ця електронна адреса захищена від спам-ботів. Вам необхідно увімкнути JavaScript, щоб побачити її.
  • Пн-Пт 09:00-18:00

Mikrotik Firmware Updates

Feed for newest RouterOS updates.
  1. 7.3beta40 changelog:

    !) queue - do not allow using CAKE type in simple and tree setups (already configured queues will be disabled);
    *) bgp - added "name" parameter for connections;
    *) bgp - fixed "keepalive-timeout" value when upgrading from RouterOS v6;
    *) bgp - fixed "l2vpn" distribution;
    *) bridge - added more details for loop detection warning;
    *) bridge - do not set VLAN on inactive port with a "set" command;
    *) bridge - ignore VLAN tagged BPDU;
    *) capsman - improved traffic processing over CAP communication tunnels:
    *) chr - fixed Cloud DDNS update after license renewal;
    *) dot1x - fixed RADIUS State attribute when client is reauthenticated;
    *) dot1x - fixed port based VLAN ID assignment on devices without a switch chip;
    *) dot1x - improved server system stability during authentication;
    *) ipsec - fixed printing of active peer statistics;
    *) l3hw - improved offloading in cases of HW table overflow for CRS305, CRS326-24G-2S+, CRS328, CRS318, CRS310;
    *) l3hw - optimized offloading when dealing with large volume of directly connected hosts;
    *) lte - added SMS sending support for MBIM protocol;
    *) lte - allow only MCC/NMC format in "operator" parameter;
    *) lte - clear SIM values when modem in "stopped" state;
    *) mpls - improved LDP AF selection process and behavior;
    *) ntp - do not allow setting port number in "server" parameter;
    *) ovpn - adjusted SHA2 authentication algorithm naming to allow legacy OpenVPN implementations to connect;
    *) ovpn - improved server stability under continous overload;
    *) ovpn - reply with the same IP address that the connection was established to;
    *) ppp - added support for VRF;
    *) romon - fixed VLAN tagged packet processing;
    *) route - fixed IPv6 /127 route nexthop resolution;
    *) routerboot - prevent enabling "protected-routerboot" on unsupported factory firmware versions;
    *) sfp - fixed link flap for QSFP+ and QSFP28 ports connected with a breakout cable, in cases where the base interface changes "running" state (introduced in v7.3beta33);
    *) sfp - hide empty monitor values in console;
    *) snmp - added VRF support (CLI only);
    *) snmp - fixed reported disk size when multiple external disks are attached;
    *) snmp - report "ifSpeed" as 0 if value out of bounds (use "ifHighSpeed" for high speed interfaces instead);
    *) ssh - added AES-GCM cipher support;
    *) ssh - removed DSA public key authentication support;
    *) supout - added simplified IPv4 and IPv6 routing table prints;
    *) switch - fixed "switch-cpu" port stats for 98DXxxxx and 98PX1012 switches (introduced in v7.3beta37);
    *) switch - fixed missing stats in traffic-monitor for 98DXxxxx and 98PX1012 switches;
    *) system - fixed Kernel timer consistency;
    *) tunnels - improved packet handling over EoIP, IPIP and GRE tunnels;
    *) vpls - fixed TE transport path usage after startup;
    *) vrrp - fixed learning of bridged local MAC addreses;
    *) winbox - added missing "IBGP", "EBGP", "Limit Exceeded" and "Stopped" parameters under "Routing/BGP/Sessions" menu;
    *) winbox - added missing "Keep Sent Attributes" parameter under "Routing/BGP/Connection" menu;
    *) winbox - added missing "Scan List" parameter for W60G interfaces;
    *) winbox - added missing BGP session commands;
    *) winbox - added support for 2.5Gbps and 100Gbps Ethernet speed options;
    *) winbox - do not show "Session Uptime" parameter under "LTE" menu if not supported by modem;
    *) winbox - fixed "Disconnect Timeout" parameter type under "CAPsMAN" menu;
    *) winbox - fixed "IP/Cloud" window refreshing after changes are detected;
    *) winbox - properly load band values under "LTE" menu;
    *) winbox - removed obsolete "Routing Table" parameter under "IP/Firewall" menu;

    Download the new 'RouterOS 7.3beta40' version here: https://mikrotik.com/download

  2. 7.2.3 changelog:

    *) system - fixed RouterOS bootup when wifiwave2 package is installed (introduced in v7.2.2);

    Download the new 'RouterOS 7.2.3' version here: https://mikrotik.com/download

  3. 7.2.2 changelog:

    *) bgp - added initial support for prefix limit;
    *) bgp - improved stability when editing BGP template;
    *) bonding - fixed LACP flapping for RB5009 and CCR2004-16G-2S+ devices;
    *) ccr - added visible "passthrough" flag for interfaces on CCR2004-1G-2XS-PCIe;
    *) ccr - usability and stability improvements for passthrough interfaces on CCR2004-1G-2XS-PCIe;
    *) cd-install - allow selecting on which drive to install RouterOS;
    *) conntrack - limited full Connection Tracking warning to 1 message per minute;
    *) crs3xx - fixed storm rate on 1Gbps interfaces for CRS354 devices;
    *) defconf - suggest user to set up new password;
    *) dhcpv4-server - fixed minor logging typo;
    *) fetch - improved full disk detection;
    *) filesystem - fixed possible boot failure on RB850Gx2 and RB1100AHx2;
    *) filesystem - improved long-term filesystem stability and data integrity;
    *) gps - fixed minor value unit typo;
    *) ipv6 - removed bogus commands from IPv6 neighbors menu;
    *) l3hw - improved offloading for directly connected hosts on CRS305, CRS326-24G-2S+, CRS328, CRS318, CRS310;
    *) l3hw - improved route table offloading for CRS317, CRS309, CRS312, CRS326-24S+2Q+, CRS354, CRS5xx, CCR2x16 devices;
    *) leds - fixed ethernet LED behavior on wAP R ac;
    *) leds - fixed wireless related LED behavior with WW2 package;
    *) lte - added SMS sending support for MBIM protocol;
    *) lte - added support for generic PXA1802 based modems;
    *) lte - disabled wait for LTE auto attach;
    *) lte - hide slave interfaces from export;
    *) lte - improved stability when upgrading LTE firmware on Chateau 5G;
    *) mlag - fixed MAC address moving between bridge ports;
    *) mpls - do MPLS forwarding for nexthops without mappings;
    *) mpls - fixed MPLS MTU and path MTU selection;
    *) mpls - fixed MPLS forwarding after any interface configuration parameter is changed;
    *) ospf - fixed GRE interface compatibility with OSPF;
    *) ospf - improved stability when enabling or removing interface-template entries;
    *) ovpn - fixed memory leak on TILE architecture;
    *) ovpn - fixed packet processing on MT7621A;
    *) ovpn - improved Windows client disconnect procedure in UDP mode;
    *) ovpn - improved service stability when processing frequent disconnects in UDP mode;
    *) ovpn - improved stability when forwarding traffic on TILE;
    *) ping - fixed socket allocation after VRF change;
    *) ppp - fixed "remote-ipv6-prefix" parameter unsetting;
    *) ppp - fixed active sessions sometimes getting stuck;
    *) ppp - fixed issue with multiple active sessions when "only-one" is enabled;
    *) queues - improved stability in large list of queue scenarios;
    *) rb5009 - fixed 10G linking issues with Intel X520, XXV710 NICs;
    *) route - fixed "table" menu emptying after RouterOS upgrade;
    *) route - fixed static routes in VRF becoming invalid after reboot;
    *) route-filter - fixed community matchers;
    *) rsvp-te - improved stability when "Resv" received for non-existing session;
    *) supout - added RIP section;
    *) system - fixed IP service initialization in VRF after system startup;
    *) system - fixed rare partial loss of RouterOS configuration after package upgrade/downgrade/install/uninstall;
    *) torch - properly capture all related IPv6 traffic;
    *) upnp - improved stability when processing incomplete HTTP header;
    *) vpls - fixed "pw-l2mtu" parameter usage;
    *) vrf - fixed VRF leaking;
    *) winbox - do not show "unknown" area under "Routing/OSPF/LSA" menu;
    *) winbox - do not show type value for NXDOMAIN entries under "IP/DNS/Cache" menu;
    *) winbox - made "Interface Templates" table sortable under "Routing/OSPF" menu;
    *) winbox - properly clean up SFP module information after it is unplugged;
    *) winbox - properly clean up disk after a failed file upload;
    *) winbox - show PVID column by default under "Bridge" menu;
    *) wireless - fixed EAP-TLS authentication;
    *) wireless - fixed GUD version in 3gpp information;
    *) ww2 - fixed VLAN tag handling;
    *) x86 - improved support for i40e driver;
    *) x86 - improved support for Intel E810 NIC;

    Download the new 'RouterOS 7.2.2' version here: https://mikrotik.com/download

  4. 7.3beta37 changelog:

    *) bonding - fixed LACP flapping for RB5009 and CCR2004-16G-2S+ devices;
    *) bridge - fixed packet marking for IP/IPv6 firewall;
    *) dot1x - improved server stability when using re-authentication;
    *) fetch - improved full disk detection;
    *) gps - fixed minor value unit typo;
    *) l3hw - improved offloading for directly connected hosts on CRS305, CRS326-24G-2S+, CRS328, CRS318, CRS310;
    *) led - fixed QSFP+, QSFP28 activity LEDs when using 40Gbps modules (introduced in v7.3beta33);
    *) lte - disabled wait for LTE auto attach;
    *) mpls - fixed MPLS MTU and path MTU selection;
    *) ovpn - fixed hardware offloading support on CHR;
    *) ovpn - improved Windows client disconnect procedure in UDP mode;
    *) ovpn - moved authentication failure messages to "info" logging level;
    *) ppp - added warning when using prefix length other than /64 for router advertisement;
    *) ppp - fixed "remote-ipv6-prefix" parameter unsetting;
    *) ppp - fixed issue with multiple active sessions when "only-one" is enabled;
    *) routerboot - properly reset system configuration when protected bootloader is enabled and reset button used;
    *) rsvp-te - improved stability when "Resv" received for non-existing session;
    *) sfp - improved QSFP/SFP interface initialization for 98DXxxxx switches;
    *) switch - fixed missing stats from traffic-monitor for 98DXxxxx and 98PX1012 switches;
    *) system - fixed RouterOS bootup when wifiwave2 package is installed (introduced in v7.3beta34);
    *) system - fixed rare partial loss of RouterOS configuration after package upgrade/downgrade/install/uninstall;
    *) user-manager - improved stability when received EAP attribute with non-existing state attribute;
    *) vpls - fixed "pw-l2mtu" parameter usage;

    Download the new 'RouterOS 7.3beta37' version here: https://mikrotik.com/download

  5. 7.3beta34 changelog:

    *) bgp - improved stability when editing BGP template;
    *) ccr - added "passthrough" flag for interfaces on CCR2004-1G-2XS-PCIe;
    *) dhcpv4-server - added "age" parameter for dynamic leases;
    *) dhcpv4-server - fixed minor logging typo;
    *) export - fixed value ID exporting that does not refer to any name;
    *) fetch - fixed SFTP upload;
    *) filesystem - fixed possible boot failure on RB850Gx2 and RB1100AHx2;
    *) filesystem - improved long-term filesystem stability and data integrity;
    *) ipsec - fixed IPsec IRQ initialization on startup on TILE;
    *) leds - fixed ethernet LED behavior on wAP R ac;
    *) lte - disabled extended signal info query for Telit LN940 module;
    *) ospf - fixed GRE interface compatibility with OSPF;
    *) ospf - improved stability when enabling or removing interface-template entries;
    *) ovpn - improved stability when forwarding traffic on TILE;
    *) ping - fixed socket allocation after VRF change;
    *) ppp - fixed active sessions sometimes getting stuck;
    *) queues - improved stability in large list of queue scenarios;
    *) rb5009 - fixed 10G linking issues with Intel X520, XXV710 NICs;
    *) ssh - fail non-interactive client after first invalid password;
    *) supout - added IGMP-Proxy section;
    *) winbox - added "Comment" parameter for BGP templates and connections;
    *) winbox - made "Interface Templates" table sortable under "Routing/OSPF" menu;
    *) winbox - made "MPLS Interface" table sortable under "MPLS" menu;
    *) winbox - made 56 the default ping size;
    *) winbox - moved "src-address-list" and "dst-address-list" parameters to "General" tab under "IPv6/Firewall" menu;
    *) winbox - show correct file system type under "System/Disks" menu;

    Download the new 'RouterOS 7.3beta34' version here: https://mikrotik.com/download

  6. 6.49.6 changelog:

    *) led - fixed wireless signal strength led on Cube Lite60;
    *) routerboot - fixed packet receiving in etherboot on Wireless Wire nRAY;
    *) winbox - added missing "3GGP RAW" parameter under "Interface/Wireless/Interworking Profile" menu;
    *) wireless - fixed GUD version in 3gpp information;

    Download the new 'RouterOS 6.49.6' version here: https://mikrotik.com/download

  7. 7.2.1 changelog:

    *) filesystem - improved long-term filesystem stability and data integrity;

    Download the new 'RouterOS 7.2.1' version here: https://mikrotik.com/download

  8. 7.3beta33 changelog:

    *) bgp - added initial support for prefix limit;
    *) bonding - added "lacp-user-key" setting;
    *) ccr - added visible "passthrough" flag for interfaces on CCR2004-1G-2XS-PCIe;
    *) ccr - usability and stability improvements for passthrough interfaces on CCR2004-1G-2XS-PCIe;
    *) cd-install - allow selecting on which drive to install RouterOS;
    *) conntrack - limited full Connection Tracking warning to 1 message per minute;
    *) dhcpv4-server - added "age" parameter for dynamic leases;
    *) dhcpv4-server - fixed conflicting or declined lease detection when IP pool differs from server's configuration;
    *) filesystem - improved UBIFS stability and data integrity after downgrade to RouterOS v6 and upgrade to RouterOS v7;
    *) gps - added GPS package support for Chateau devices;
    *) ipv6 - added "ra-preference" parameter support for RA;
    *) ipv6 - removed bogus commands from IPv6 neighbors menu;
    *) l3hw - improved route table offloading for CRS317, CRS309, CRS312, CRS326-24S+2Q+, CRS354, CRS5xx, CCR2x16 devices;
    *) leds - fixed wireless related LED behavior with WW2 package;
    *) lora - do not allow setting non-existing forwarding server;
    *) lora - fixed bogus TOO_EARLY errors;
    *) lora - removed TX lookup table;
    *) lte - added MCS, CQI and RI value reporting for Fibocom FG621;
    *) lte - added SMS sending support for MBIM protocol;
    *) lte - added support for generic PXA1802 based modems;
    *) lte - disabled wait for LTE auto attach;
    *) lte - expose diagnostics channel for all modems;
    *) lte - fixed LTE firwmare upgrade on RBLtAP-2HnD with R11e-LTE6;
    *) lte - fixed Sierra MC7455 modem initialization;
    *) lte - hide slave interfaces from export;
    *) lte - improved stability when configuring multiple APN's at the same time in MBIM mode;
    *) lte - improved stability when upgrading LTE firmware on Chateau 5G;
    *) mlag - fixed MAC address moving between bridge ports;
    *) mpls - do MPLS forwarding for nexthops without mappings;
    *) mpls - fixed MPLS forwarding after any interface configuration parameter is changed;
    *) ntp - fixed "use-local-clock" behavior when enabling server;
    *) ovpn - fixed memory leak on TILE architecture;
    *) ovpn - fixed packet processing on MT7621A;
    *) ovpn - improved service stability when outbound packets are blocked by firewall in UDP mode;
    *) ovpn - improved service stability when processing frequent disconnects in UDP mode;
    *) port - do not loose "parity" setting;
    *) route - fixed "nexthop" table printing;
    *) route - fixed "table" menu emptying after RouterOS upgrade;
    *) route - fixed static routes in VRF becoming invalid after reboot;
    *) route-filter - fixed community matchers;
    *) routerboard - fixed USB bus numbering on LtAP and M33G;
    *) routerboot - added extra shortcut information on how to boot into etherboot;
    *) sfp - added 2.5Gbps rate for SFP+ and QSFP+ interfaces on 98DXxxxx and 98PX1012 switches (requires disabled auto-negotiation);
    *) sfp - improved Q/SFP interface initialization and stability for 98DXxxxx and 98PX1012 switches;
    *) snmp - hide Vendor ID in DHCP MIB when branding is present;
    *) supout - added IGMP-Proxy section;
    *) supout - added NTP servers section;
    *) supout - added PIMSM section;
    *) supout - added RIP section;
    *) supout - added WireGuard section;
    *) switch - added option to match source and destination IP addresses in ARP packets for RB5009 (requires mac-protocol=arp setting);
    *) system - fixed IP service initialization in VRF after system startup;
    *) torch - properly capture all related IPv6 traffic;
    *) tr069-client - fixed RPC download of "1 Vendor Configuration File" with branding package;
    *) upnp - improved stability when processing incomplete HTTP header;
    *) user-manager - added "Acct-Interim-Interval" to predefined attribute list;
    *) w60g - improved stability on Cube 60Pro ac and CubeSA 60Pro ac;
    *) webfig - properly show all routing table content;
    *) winbox - added "ra-preference" parameter under "IPv6/ND" menu;
    *) winbox - added SKID and AKID parameters under "Certificate" menu;
    *) winbox - added warning message for LTE upgrade process;
    *) winbox - do not auto start Wireless Sniffer when opened;
    *) winbox - do not show "unknown" area under "Routing/OSPF/LSA" menu;
    *) winbox - do not show type value for NXDOMAIN entries under "IP/DNS/Cache" menu;
    *) winbox - fixed graph drawing in QuickSet;
    *) winbox - fixed hex type values under "User Manager" menu;
    *) winbox - fixed typo in ZeroTier instance title;
    *) winbox - minimal required version is v3.33;
    *) winbox - moved "src-address-list" and "dst-address-list" parameters to "General" tab under "IP/Firewall" menu;
    *) winbox - properly clean up SFP module information after it is unplugged;
    *) winbox - properly clean up disk after a failed file upload;
    *) winbox - show "System/RouterBOARD/Mode Button" on devices that have such feature;
    *) winbox - show PVID column by default under "Bridge" menu;
    *) winbox - take into account timezone for timed values under "User Manager" menu;
    *) wireless - fixed "wmm-support=required" checking;
    *) wireless - fixed EAP-TLS authentication;
    *) wireless - fixed GUD version in 3gpp information;
    *) ww2 - fixed VLAN tag handling;
    *) x86 - improved support for Intel E810 NIC;
    *) zerotier - added support for Controller configuration;

    Download the new 'RouterOS 7.3beta33' version here: https://mikrotik.com/download

  9. 7.2 changelog:

    *) api - accept "Content-Type" with specified charset;
    *) arm - fixed "auto" CPU frequency setting;
    *) arm - fixed "shutdown" command on hAP ac^2;
    *) arm64 - improved Watchdog initiated reboot reason reporting;
    *) arm64 - improved low disk space handling condition on upgrade;
    *) backup - added "force-v6-to-v7-configuration-upgrade" option on backup load to clear RouterOS v7 configuration and trigger reimport of RouterOS v6 route configuration (CLI only);
    *) backup - fixed automatic backup generation when resetting configuration;
    *) backup - fixed cloud backup's creation timezone;
    *) bgp - added BGP advertisements display (requires output.keep-sent-attributes to be set);
    *) bgp - do not export default BGP values;
    *) bgp - fixed VPNv4 route sending to remote peer;
    *) bgp - fixed link-local iBGP address selection;
    *) bgp - fixed network advertisement from address-lists after reboot;
    *) bgp - fixed routing table and BGP configuration order in export;
    *) bgp - improvements on detecting peers local address when IPv6 link-local addresses are used;
    *) bluetooth - allow to export device, advertiser and scanner configuration;
    *) bluetooth - disable scanning by default;
    *) bridge - added fast-path and inter-VLAN routing FastTrack support when vlan-filtering is enabled;
    *) bridge - fixed FastPath when using "frame-types=admit-only-untagged-and-priority-tagged" setting;
    *) bridge - fixed PPPoE packet forwarding when using "use-ip-firewall-for-pppoe" setting;
    *) bridge - fixed bridge filter and NAT rules on ARM64 and TILE devices;
    *) bridge - fixed destination NAT when using "use-ip-firewall" setting;
    *) bridge - fixed filter and NAT "set-priority" action;
    *) bridge - fixed filter and NAT "set-priority" on ARM64 devices;
    *) bridge - fixed filter rules when using interface lists;
    *) bridge - fixed firewall "ingress-priority" matcher and "new-priority=from-ingress" action settings from VLAN tagged frames;
    *) bridge - fixed priority tagged frame forwarding when using "frame-types=admit-only-untagged-and-priority-tagged" setting;
    *) capsman - improved stability when running background scan on CAP;
    *) capsman - improved system stability when processing CAP packet by Mangle;
    *) ccr2004 - improved PCI timeout handling on CCR2004-1G-2XS-PCIe;
    *) ccr2004 - improved system stability on CCR2004-12S+2XS;
    *) certificate - allow to choose digest algorithm for CSR signing;
    *) certificate - made "fingerprint" parameter read-only;
    *) chr - improved system stability when writing into memory;
    *) chr - temporarily suspended downgrade to RouterOS v6;
    *) clock - properly notify all instances about time changes;
    *) conntrack - properly detect helper status;
    *) console - fixed "print" command with additional "where" condition;
    *) console - improved console responsiveness when processing received characters;
    *) console - made "password" parameter mandatory when creating a new user;
    *) console - properly erase CLI history after configuration reset;
    *) console - updated copyright notice;
    *) crs1xx/2xx - fixed static switch host addresses after link down;
    *) crs1xx/2xx - ignore static bridge host addresses (switch unicast-fdb should be used instead);
    *) crs3xx - fixed CPU load balancing for ARM dual core devices;
    *) crs3xx - fixed QSFP+ interface LEDs;
    *) crs3xx - fixed watchdog timer functionality;
    *) crs3xx - improved SFP+ interface linking after reboot for CRS312 device;
    *) crs3xx - improved maximum allowed ACL rule calculation;
    *) crs3xx - improved system stability when creating many ACL rules on CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
    *) defconf - made "192.168.188.1/24" the default LAN IP address for LTE CPE devices;
    *) dhcp-server - fixed DHCP Option decimal value parsing;
    *) dhcp-server - fixed statistics sending in "Accounting Stop" packets;
    *) dhcp-server - send "Class" attribute in "Accounting Request" when provided by RADIUS;
    *) dhcpv4-server - allow adding comments;
    *) dhcpv4-server - remove dynamic leases when server configuration is removed;
    *) dhcpv4-server - reset dynamic "bcast" flag when receiving offer from DHCP relay;
    *) dhcpv4-server - reset offer counter when receiving offer from DHCP relay;
    *) dhcpv6 - added VRF support;
    *) dot1x - added "server-fail-vlan-id", "guest-vlan-id" and "reauth-timeout" settings for dot1x server;
    *) dot1x - added "src-address", "src-mac-address" and "src-port" settings for dynamic switch rules;
    *) dot1x - added NAS-Port-ID attribute for RADIUS Access-Request;
    *) dude - fixed The Dude client compatibility with RouterOS v7;
    *) dude - fixed The Dude compatibility with ARM64;
    *) ethernet - improved system stability when receiving large packets on devices with 88F3720 CPU (nRAY, LHGG);
    *) firewall - improved available port lookup for source NAT when free port range is exhausted;
    *) graphing - properly generate interface graph for traffic higher than 2.1Gbps;
    *) hotspot - fixed login page over HTTPS;
    *) hotspot - fixed memory leak on every web page loading;
    *) hotspot - fixed web page loading using HTTPS;
    *) ike2 - ignore "INITIAL-CONTACT" payload on responder when "send-initial-contact" is disabled;
    *) interface - fixed minor memory leak when interface or connected route is changed;
    *) ipsec - added hardware acceleration support for CCR2116;
    *) ipsec - fixed "identities" menu emptying after RouterOS upgrade/reboot;
    *) ipv6 - do not add duplicate dynamic prefix when static already exists;
    *) ipv6 - fixed "retransmissit-interval" unit value;
    *) ipv6 - fixed VLAN tagged PPPoE packet receiving on RB5009;
    *) l2tp - fixed CHAP challenge packet processing over IPsec;
    *) l2tp - improved service stability when disabling L2TP server with connected clients;
    *) l2tp - improved system stability when processing L2TP control messages;
    *) l3hw - added HW offloaded FastTrack support for inter-VLAN routing;
    *) l3hw - fixed HW offloaded NAT;
    *) l3hw - fixed HW offloaded routing when using 7 or more VLAN interfaces;
    *) l3hw - fixed ICMP message when routed packet exceeds MTU and DF flag is set;
    *) l3hw - fixed bonding source MAC address;
    *) l3hw - fixed default route offloading for CRS305, CRS326-24G-2S+, CRS328, netPower, netFiber devices;
    *) l3hw - improved routing table offloading for CRS305, CRS326-24G-2S+, CRS328, netPower, netFiber devices;
    *) l3hw - improved system stability when using 7 or more VLAN interfaces;
    *) led - fixed LED behavior on Audience;
    *) led - reduced LTE signal LED range to -70;
    *) leds - fixed user LED on RB750Gr3;
    *) log - added warning message when connection tracking table is full;
    *) log - include message also in e-mail body;
    *) lora - fixed "antenna-gain" parameter unit;
    *) lte - add IPv6 address on interface as well;
    *) lte - added 3 APN profile support and APN name re-using on R11e-LTE6;
    *) lte - added MAC address and IPv6 LL address persistence after reboot on EG12 and EG18 modems;
    *) lte - added basic information support for Telit LM960 and LM940 in MBIM mode;
    *) lte - added class based support for configless RNDIS LTE modems;
    *) lte - added support for Uplink CA reporting;
    *) lte - changed "CS/PS" registration type from "both" to "any" on R11e-LTE un R11e-LTE6;
    *) lte - do not loose "band" configuration after reboot on Chateau 5G;
    *) lte - do not show external antenna selector on devices that does not support it;
    *) lte - enabled multi-APN and name re-use support for Chateau;
    *) lte - expose diagnostics channel for all modems;
    *) lte - fixed "monitor" command to not report old info;
    *) lte - fixed AT command response handling on R11e-LTE;
    *) lte - fixed IPv6 address addition after startup on R11e-LTE6;
    *) lte - fixed MBIM modem reset on AT timeout;
    *) lte - fixed link flapping when loosing cellular signal on R11e-LTE un R11e-LTE6;
    *) lte - fixed packet forwarding on R11e-4G and R11e-LTE-US;
    *) lte - fixed possible timeouts when sending SMS in LTE only mode on R11e-LTE;
    *) lte - fixed support for Sierra MC7710;
    *) lte - fixed support for Telit 960;
    *) lte - improved stability on "+EGMR" response in MBIM mode;
    *) lte - improved stability when modem disappears during firmware upgrade;
    *) lte - improved support for sending/receiving SMS in LTE only mode on R11e-LTE6;
    *) lte - made "no" the default value for "use-network-apn" parameter;
    *) lte - properly recognize MBIM modem in USB port as LTE on Chateau 5G;
    *) ntp - allow adding duplicate server address if dynamic entry exists;
    *) ntp - fixed multicast mode support;
    *) ntp - improved IPv6 address support;
    *) ntp - improved service stability when none of the NTP servers are reachable for a while;
    *) ntp - improved source address usage for reply packets;
    *) ntp - print log change time with time-zone applied;
    *) ospf - added "ptmp-broadcast" interface type (compatible with RouterOSv6 PTMP type);
    *) ospf - convert ospf "static" redistribute to "static,dhcp,modem,vpn" after update from RouterOS v6;
    *) ospf - fixed MD5 authentication;
    *) ospf - fixed NBMA hello's not being sent if priority is set to 0;
    *) ospf - fixed default route origination when "default-originate=if-installed" "redistribute" is enabled;
    *) ospf - fixed default type-3 LSA's not being injected to stub area;
    *) ospf - fixed distance if "originate-default" is set to "always";
    *) ospf - fixed external LSA not updating after prefix netmask change;
    *) ospf - fixed incorrect LSA types when changing area types;
    *) ospf - fixed neighbor election failure;
    *) ospf - fixed neighbor stuck in ExStart;
    *) ospf - fixed simple authentication;
    *) ospf - general stability improvements;
    *) ospf - improved DB retransmit logging;
    *) ospf - improved logging;
    *) ospf - improved overall stability;
    *) ospf - improved stability for very large LSDB;
    *) ospf - improved stability on OSPFv3 instance disabling;
    *) ospf - improved stability when DR goes down;
    *) ospf - improves stability when handling looped back OSPF packets;
    *) ospf - properly set VRF for gateway;
    *) ospf - send notifies for neighbors;
    *) ovpn - added SHA2 authentication algorithm support;
    *) ovpn - added hardware acceleration support for IPQ4018/IPQ4019 and AL* series chipsets;
    *) ovpn - added option to send disconnect message in UDP mode;
    *) ovpn - fixed large option message parsing;
    *) ovpn - improved UDP session handling;
    *) ovpn - improved memory allocation on Tile in "ethernet" mode;
    *) ovpn - improved system stability in high load scenarios;
    *) pimsm - fixed menu prints;
    *) pimsm - general stability improvements;
    *) poe - fixed PoE driver loading on CRS354-48P-4S+2Q+;
    *) poe - update PoE firmware only on devices that support it;
    *) ppp - added "comment" option for PPPoE servers;
    *) ppp - fixed AT+CPIN chat when SIM PIN is specified;
    *) ppp - improved stability when handling large amount of connections simultaneously;
    *) ppp - show local and remote IPv6 addresses (CLI only);
    *) pppoe - added option to configure "host-uniq" parameter;
    *) pppoe - added option to ignore PADI messages with empty service name;
    *) pppoe - use default MTU of 1492;
    *) pptp - added insecure connection warning;
    *) pptp - show insecure connection warning on dynamic interfaces;
    *) qsfp - correctly display auto-negotiation status;
    *) queue - fixed queued IPv6 traffic considered as "invalid" by Firewall;
    *) queue - improved system stability when processing traffic;
    *) queue - improved system stability when using more than 255 unique packet marks;
    *) rb4011 - fixed jumbo frame processing on SFP+ port when using 1G module;
    *) rip - added logging;
    *) rip - fixed route metrics;
    *) rip - fixed route redistribution;
    *) rip - use nexthop with interface;
    *) route - allow OSPF and RIP redistributed routes to be matched by routing filters;
    *) route - fixed "min-prefix" configuration when set to 0;
    *) route - fixed "suppress-hw-offload" update;
    *) route - fixed "table" menu emptying after RouterOS upgrade;
    *) route - fixed BGP atomic aggregate value;
    *) route - fixed ECMP load balancing in FastPath;
    *) route - fixed ECMP route removal;
    *) route - fixed route addition to VRF from BGP;
    *) route - fixed router's LSA for PTP networks;
    *) route - fixed routing configuration export on SMIPS devices;
    *) route - general stability improvements;
    *) route - improved routing table print speed;
    *) route - show OSPF and RIP specific attributes in "/routing route" table;
    *) route-filter - fixed "return" action;
    *) route-filter - fixed complex matchers with "|| or and &&";
    *) route-filter - fixed incorrect invert-match configuration upgrade from RouterOS v6;
    *) route-filter - fixed range conversion after update from RouterOS v6;
    *) route-filters - allow to filter and modify default route if "originate-default" is set to "always";
    *) route-filters - fixed possible address list race condition and memory leak;
    *) route-filters - renamed "*-set" to "*-list";
    *) routerboard - fixed "ether2" interface presence on some RBwAPGR devices;
    *) routerboard - fixed WPS button functionality on Audience;
    *) routing - added PCAP viewer tool for BGP advertisements debugging purposes;
    *) routing-filter - fixed "bgp-*-communities-empty" matcher;
    *) rpki - made RPKI verify non-strict, introduces new state "unverified";
    *) rpki - show expire timer;
    *) sfp - improved SFP module detection on CRS106 and CRS112;
    *) smb - fixed SMB2.0 disk size reporting;
    *) smips - improved RAM allocation;
    *) sms - increased "at-chat" timeout when sending SMS;
    *) snmp - added SFP vendor name to optical table;
    *) snmp - added support for "ipv6AddrPrefixTable" and "ipv6RouteNumber" OID's;
    *) snmp - allow two level nesting for vlan, bonding speed query;
    *) socks - fixed SOCKS5 support;
    *) ssh - fixed forwarding with IPv6 link-local addresses;
    *) ssl - fixed CA certificate processing when "subjAltName" is marked as critical;
    *) supout - added "port-controller" bridge section;
    *) switch - added "rx-overflow" counter for 88E6393X (RB5009) and 88E6191X (CCR2004-16G-2S+) switch chips;
    *) switch - fixed port-isolation misconfiguration detection when using multiple switches;
    *) switch - improved packet forwarding with enabled "cpu-flow-control" setting between different rate interfaces for 88E6393X (RB5009) and 88E6191X (CCR2004-16G-2S+) switch chips;
    *) switch - improved switch chip initialization process on bootup for CCR2004-16g-2s+ devices;
    *) switch - properly limit maximum number of switch rules to 256 on RB5009;
    *) system - fixed license loss on some RB1100Dx4 and RB4011 devices;
    *) tr069-client - accept 200-299 codes for HTTP diagnostics;
    *) tr069-client - added support for 5G band configuration;
    *) tr069-client - added support for wireless "skip-DFS" configuration;
    *) tr069-client - added support for wireless client uptime reporting;
    *) tr069-client - fixed RPC download of "3 Vendor Configuration File" with branding package;
    *) traffic-flow - do not handle NAT events when "nat-events" is disabled;
    *) traffic-generator - fixed transmit speed for multiple asymmetric streams;
    *) upgrade - improved 404 error handling when checking for new versions;
    *) upgrade - improved downgrade prompt message;
    *) ups - fixed UPS support;
    *) usb - fixed display of incorrect port count for USB serial ports;
    *) user - removed obsolete "tikapp" policy;
    *) user - send "Class" attribute in "Accounting Request" when provided by RADIUS;
    *) vlan - fixed improper VLAN priority addition for routed packets;
    *) vxlan - allow unsetting "group" and "interface" properties;
    *) vxlan - fixed running state after reboot when using "interface" and "group" settings;
    *) webfig - do not show side menu if WebFig is disabled by skin;
    *) webfig - fixed default configuration popup presence;
    *) webfig - fixed user policy lookup for skin designer;
    *) wifiwave2 - added "client-isolation" feature;
    *) wifiwave2 - added support for handling disconnect request messages from RADIUS servers;
    *) wifiwave2 - fixed calling "scan" and "frequency-scan" commands through the API;
    *) winbox - added "Disconnect Notify" checkbox to "Interface/OVPN Client" menu;
    *) winbox - added "Freq. Usage" and "Scan" buttons for WifiWave2 interfaces;
    *) winbox - added "Ignore Missing" selector to "System/Packages" menu;
    *) winbox - added "Mode" parameter under "Wireless" menu with WifiWave2 package;
    *) winbox - added "Routing Table" parameter for IPv6 routes;
    *) winbox - added "TLS Version" parameter for "Interface/OVPN";
    *) winbox - added "VPN" tab to "Routing/BGP" menu;
    *) winbox - added "VRF" parameter for "SSH" and "Telnet" menus;
    *) winbox - added "VRF" parameter to "IP/Services" menu;
    *) winbox - added "comment" parameter to "User Manager/Users" menu;
    *) winbox - added "host-uniq" parameter to PPPoE client interface;
    *) winbox - added MLAG support;
    *) winbox - added SHA256 and SHA512 "Auth" values for OVPN menu's;
    *) winbox - added ZeroTier support;
    *) winbox - added explicit "Upload" and "Download" names for "Bucket Size" parameters under "Queues" menu;
    *) winbox - added interface list support for "IP/Traffic Flow" menu;
    *) winbox - added local/remote CPU load parameters for "Bandwidth Test";
    *) winbox - added missing "3GGP RAW" parameter under "Interface/Wireless/Interworking Profile" menu;
    *) winbox - added missing "accounting", "interim-update" and "radius-password" parameters under "IP/DHCP Server" menu;
    *) winbox - added support for "Tool/Speedtest" menu;
    *) winbox - added support for W60G align tool;
    *) winbox - allow adding more than 100 tagged/untagged interfaces under "Bridge/VLAN" menu;
    *) winbox - allow configuring "VTEP" under "Interface/VXLAN" menu;
    *) winbox - allow setting "Interface" parameter for 100G LED types;
    *) winbox - changed "Accept Redirects" parameter type under "IPv6/Settings" menu;
    *) winbox - do not require "name" and "file name" parameters for certificate import/export;
    *) winbox - do not show "Antenna Scan" button on devices that do not support it;
    *) winbox - do not show connection tracking table if it has more than 10000 entries;
    *) winbox - fixed "00:00:00" time printing;
    *) winbox - fixed "Switch" menu on Chateau devices;
    *) winbox - fixed "action" field in "IP/Web Proxy/Access" menu;
    *) winbox - fixed "expires-after" certificate parameter value;
    *) winbox - fixed CHR License renewing process;
    *) winbox - fixed address list type parameters in "Routing" menu;
    *) winbox - fixed content filtering in "Tools/Packet Sniffer/Packets" menu;
    *) winbox - fixed entry order in "Tools/Packet Sniffer/Packets" menu;
    *) winbox - fixed error message when adding NTH rule with "0" value;
    *) winbox - fixed minor typo under "LTE" interface menu;
    *) winbox - fixed switch related settings for MT7621 switch chip (hEX, hEX S, RBM33G, RBM11G, LtAP);
    *) winbox - made "9" the default value for "Target" parameter under "IP/Traffic Flow" menu;
    *) winbox - made "Routing Filters/Rules" table sortable;
    *) winbox - made OSPF interface type names consistent between CLI and GUI;
    *) winbox - moved "IP/Route/Nexthops" and "IPv6/Route/Nexthops" menus to "Routing/Nexthops";
    *) winbox - moved IPv4 and IPv6 "Rules" menus under "Routing" menu;
    *) winbox - properly limit "Disconnect Timeout" value under "CAPsMAN/Configuration" menu;
    *) winbox - properly save "IPv6/Settings" menu in session file;
    *) winbox - properly show "v" flag instead of "y" under "IP/Route" menu;
    *) winbox - properly update ethernet auto negotiation status on CHR;
    *) winbox - properly update server list under "System/NTP Client/Servers" menu;
    *) winbox - renamed "Keep user configuration" to "Keep users" under "System/Reset Configuration" menu;
    *) winbox - renamed "MBPS" to "Mbps" value unit name in "Tools/Traffic Generator" menu;
    *) winbox - renamed "Revoked" parameter to "Revoked Time" under "System/Certificates" menu;
    *) winbox - report local terminal session as "local" instead of "telnet";
    *) winbox - require existing pool for "Address Pool" parameter under "IPv6/DHCP Server" menu;
    *) winbox - require non empty "Packet Mark" value under "Queues" menu;
    *) winbox - show "H" flag for offloaded connections in "IP/Firewall/Connections" menu;
    *) winbox - show "Lost Ratio" column by default under "Tools/Traffic Generator" menu;
    *) winbox - show "Routes" column by default under "PPP/Secrets" menu;
    *) winbox - show "System/Health/Settings" only on boards that have configurable values;
    *) winbox - show "System/SwOS" menu only on boards that have dual boot;
    *) winbox - show additional columns by default for "Wireless" menu with WifiWave2 package;
    *) winbox - sort "Address List" parameter values alphabetically in "IP/DHCP Server/Leases" menu;
    *) winbox - updated default "Routing/BGP/Peer Cache" table appearance;
    *) winbox - use "total" as default value for "Tools/Profile";
    *) wireguard - allow same peer's public key for different interfaces;
    *) wireguard - fixed IPv6 LL address generation;
    *) wireguard - fixed IPv6 traffic processing with multiple peers;
    *) wireguard - made "preshared-key" and "private-key" values sensitive;
    *) wireless - added "3gpp-info" parameter to interworking configuration;
    *) wireless - added EAP-AKA to interworking's realm configuration;
    *) wireless - added information about client signal strength to log messages about disconnections;
    *) wireless - correctly preserve WMM priority when receiving packets;
    *) wireless - fixed frequency range information for IPQ4019 interfaces;
    *) wireless - fixed interface initialization on Metal 2SHPn;
    *) wireless - improved nv2 link stability;
    *) wireless - improved wireless connection stability during background scans;
    *) www - fixed "tls-version" for SSL;
    *) x86 - added support for Intel E810 NIC;
    *) x86 - allow to select disk for install image;
    *) x86 - fixed NVME partition path;
    *) x86 - fixed VLAN tagged packet transmit;
    *) x86 - made "no" the default value for "disable-running-check" ethernet parameter;
    *) x86 - properly distinguish multiple NICs that share the same PCI bus number;
    *) zerotier - fixed IPv6 support;
    *) zerotier - made MAC and MTU values read-only;
    *) zerotier - properly handle IP address change;

    Download the new 'RouterOS 7.2' version here: https://mikrotik.com/download

  10. 7.2rc7 changelog:

    *) route - allow OSPF and RIP redistributed routes to be matched by routing filters;

    Download the new 'RouterOS 7.2rc7' version here: https://mikrotik.com/download

  11. 7.2rc6 changelog:

    *) ccr2004 - improved PCI timeout handling on CCR2004-1G-2XS-PCIe;
    *) dude - fixed The Dude compatibility with ARM64;
    *) l2tp - improved service stability when disabling L2TP server with connected clients;
    *) l3hw - fixed default route offloading for CRS305, CRS326-24G-2S+, CRS328, netPower, netFiber devices;
    *) lte - enabled multi-APN and name re-use support for Chateau;
    *) lte - improved stability when modem disappears during firmware upgrade;
    *) ntp - improved source address usage for reply packets;
    *) ospf - properly set VRF for gateway;
    *) poe - fixed PoE driver loading on CRS354-48P-4S+2Q+;
    *) route - allow OSPF and RIP redistributed routes to be matched by routing filters;
    *) route - fixed "table" menu emptying after RouterOS upgrade;
    *) switch - properly limit maximum number of switch rules to 256 on RB5009;
    *) tr069-client - fixed RPC download of "3 Vendor Configuration File" with branding package;
    *) x86 - fixed VLAN tagged packet transmit;

    Download the new 'RouterOS 7.2rc6' version here: https://mikrotik.com/download

  12. 7.2rc5 changelog:

    *) api - accept "Content-Type" with specified charset;
    *) arm - fixed "auto" CPU frequency setting;
    *) arm64 - improved Watchdog initiated reboot reason reporting;
    *) backup - fixed cloud backup's creation timezone;
    *) bgp - added BGP advertisements display (requires output.keep-sent-attributes to be set);
    *) bgp - fixed link-local iBGP address selection;
    *) bgp - fixed network advertisement from address-lists after reboot;
    *) bridge - fixed firewall "ingress-priority" matcher and "new-priority=from-ingress" action settings from VLAN tagged frames;
    *) ccr2004 - improved system stability on CCR2004-12S+2XS;
    *) crs1xx/2xx - fixed static switch host addresses after link down;
    *) crs1xx/2xx - ignore static bridge host addresses (switch unicast-fdb should be used instead);
    *) dhcpv6 - added VRF support;
    *) dude - fixed The Dude client compatibility with RouterOS v7;
    *) firewall - improved available port lookup for source NAT when free port range is exhausted;
    *) ipsec - fixed "identities" menu emptying after RouterOS upgrade/reboot;
    *) ipv6 - do not add duplicate dynamic prefix when static already exists;
    *) ipv6 - fixed "retransmissit-interval" unit value;
    *) ipv6 - fixed VLAN tagged PPPoE packet receiving on RB5009;
    *) l2tp - fixed CHAP challenge packet processing over IPsec;
    *) l3hw - improved routing table offloading for CRS305, CRS326-24G-2S+, CRS328, netPower, netFiber devices;
    *) led - fixed LED behavior on Audience;
    *) led - reduced LTE signal LED range to -70;
    *) log - added warning message when connection tracking table is full;
    *) lte - add IPv6 address on interface as well;
    *) lte - added support for Uplink CA reporting;
    *) lte - changed "CS/PS" registration type from "both" to "any" on R11e-LTE un R11e-LTE6;
    *) lte - do not loose "band" configuration after reboot on Chateau 5G;
    *) lte - fixed AT command response handling on R11e-LTE;
    *) lte - fixed MBIM modem reset on AT timeout;
    *) lte - fixed link flapping when loosing cellular signal on R11e-LTE un R11e-LTE6;
    *) ntp - improved service stability when none of the NTP servers are reachable for a while;
    *) ospf - general stability improvements;
    *) ospf - improved DB retransmit logging;
    *) ospf - send notifies for neighbors;
    *) ovpn - improved memory allocation on Tile in "ethernet" mode;
    *) ovpn - improved system stability in high load scenarios;
    *) pimsm - fixed menu prints;
    *) pimsm - general stability improvements;
    *) queue - fixed queued IPv6 traffic considered as "invalid" by Firewall;
    *) rb4011 - fixed jumbo frame processing on SFP+ port when using 1G module;
    *) rip - added logging;
    *) rip - fixed route metrics;
    *) rip - fixed route redistribution;
    *) rip - use nexthop with interface;
    *) route - fixed "table" menu emptying after RouterOS upgrade;
    *) route - fixed BGP atomic aggregate value;
    *) route - fixed ECMP route removal;
    *) route - general stability improvements;
    *) routerboard - fixed "ether2" interface presence on some RBwAPGR devices;
    *) routerboard - fixed WPS button functionality on Audience;
    *) routing - added PCAP viewer tool for BGP advertisements debugging purposes;
    *) routing-filter - fixed "bgp-*-communities-empty" matcher;
    *) sfp - improved SFP module detection on CRS106 and CRS112;
    *) smips - improved RAM allocation;
    *) switch - added "rx-overflow" counter for 88E6393X (RB5009) and 88E6191X (CCR2004-16G-2S+) switch chips;
    *) switch - improved packet forwarding with enabled "cpu-flow-control" setting between different rate interfaces for 88E6393X (RB5009) and 88E6191X (CCR2004-16G-2S+) switch chips;
    *) tr069-client - added support for 5G band configuration;
    *) tr069-client - added support for wireless "skip-DFS" configuration;
    *) winbox - added missing "3GGP RAW" parameter under "Interface/Wireless/Interworking Profile" menu;
    *) winbox - added missing "accounting", "interim-update" and "radius-password" parameters under "IP/DHCP Server" menu;
    *) winbox - allow adding more than 100 tagged/untagged interfaces under "Bridge/VLAN" menu;
    *) winbox - allow configuring "VTEP" under "Interface/VXLAN" menu;
    *) winbox - fixed "00:00:00" time printing;
    *) winbox - fixed switch related settings for MT7621 switch chip (hEX, hEX S, RBM33G, RBM11G, LtAP);
    *) winbox - moved IPv4 and IPv6 "Rules" menus under "Routing" menu;
    *) winbox - properly show "v" flag instead of "y" under "IP/Route" menu;
    *) winbox - properly update server list under "System/NTP Client/Servers" menu;
    *) winbox - show "System/Health/Settings" only on boards that have configurable values;
    *) www - fixed "tls-version" for SSL;
    *) x86 - allow to select disk for install image;
    *) x86 - fixed NVME partition path;
    *) zerotier - fixed IPv6 support;

    Download the new 'RouterOS 7.2rc5' version here: https://mikrotik.com/download

  13. 7.1.5 changelog:

    *) route - fixed "table" menu emptying after RouterOS upgrade;

    Download the new 'RouterOS 7.1.5' version here: https://mikrotik.com/download

  14. 7.1.4 changelog:

    *) bgp - fixed VPNv4 route sending to remote peer;
    *) bridge - fixed destination NAT when using "use-ip-firewall" setting;
    *) bridge - fixed filter rules when using interface lists;
    *) bridge - fixed priority tagged frame forwarding when using "frame-types=admit-only-untagged-and-priority-tagged" setting;
    *) capsman - improved stability when running background scan on CAP;
    *) crs3xx - improved maximum allowed ACL rule calculation;
    *) crs3xx - improved system stability when creating many ACL rules on CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
    *) l2tp - improved system stability when processing L2TP control messages;
    *) lte - made "no" the default value for "use-network-apn" parameter;
    *) lte - made "RG502QEAAAR11A06M4G" the last OTA firmware version update for Chateau 5G in RouterOS 7.1.x release tree;
    *) ntp - improved source address usage for reply packets;
    *) ospf - fixed default route origination when "default-originate=if-installed" "redistribute" is enabled;
    *) ospf - fixed incorrect LSA types when changing area types;
    *) ppp - added "comment" option for PPPoE servers;
    *) queue - improved system stability when using more than 255 unique packet marks;
    *) route - fixed ECMP load balancing in FastPath;
    *) route - fixed route addition to VRF from BGP;
    *) route - fixed routing configuration export on SMIPS devices;
    *) route-filters - renamed "*-set" to "*-list";
    *) sfp - improved SFP module detection on CRS106 and CRS112;
    *) switch - fixed port-isolation misconfiguration detection when using multiple switches;
    *) traffic-flow - do not handle NAT events when "nat-events" is disabled;
    *) ups - fixed UPS support;
    *) winbox - added "VPN" tab to "Routing/BGP" menu;
    *) winbox - added "VRF" parameter for "SSH" and "Telnet" menus;
    *) winbox - do not show "Antenna Scan" button on devices that do not support it;
    *) wireguard - allow same peer's public key for different interfaces;
    *) wireless - added "3gpp-info" parameter to interworking configuration;
    *) wireless - added EAP-AKA to interworking's realm configuration;
    *) wireless - fixed interface initialization on Metal 2SHPn;

    Download the new 'RouterOS 7.1.4' version here: https://mikrotik.com/download

  15. 6.49.5 changelog:

    *) defconf - fixed invalid default password setting after configuration reset (introduced in v6.49.4);
    *) sfp - improved SFP module detection on CRS106 and CRS112;

    Download the new 'RouterOS 6.49.5' version here: https://mikrotik.com/download

  16. 6.49.4 changelog:

    *) capsman - improved stability when running background scan on CAP;
    *) lora - fixed "antenna-gain" parameter unit;
    *) ssl - disabled RC4 and 3DES ciphers for "www-ssl", "www-api" and OVPN services;
    *) traffic-flow - do not handle NAT events when "nat-events" is disabled;
    *) wireless - added "3gpp-info" parameter to interworking configuration;
    *) wireless - added EAP-AKA to interworking's realm configuration;
    *) wireless - correctly preserve WMM priority when receiving packets;
    *) wireless - updated "philippines" regulatory domain information;

    Download the new 'RouterOS 6.49.4' version here: https://mikrotik.com/download

  17. 7.2rc4 changelog:

    *) bgp - fixed VPNv4 route sending to remote peer;
    *) bridge - fixed FastPath when using "frame-types=admit-only-untagged-and-priority-tagged" setting;
    *) bridge - fixed IP address on untagged bridge interface when vlan-filtering is enabled (introduced in v7.2rc2);
    *) bridge - fixed PPPoE packet forwarding when using "use-ip-firewall-for-pppoe" setting;
    *) bridge - fixed destination NAT when using "use-ip-firewall" setting;
    *) bridge - fixed filter and NAT "set-priority" on ARM64 devices;
    *) bridge - fixed filter rules when using interface lists;
    *) bridge - fixed priority tagged frame forwarding when using "frame-types=admit-only-untagged-and-priority-tagged" setting;
    *) console - fixed terminal repainting on F5 and CTRL+L key press (introduced in v7.2rc2);
    *) crs3xx - fixed watchdog timer functionality;
    *) crs3xx - improved maximum allowed ACL rule calculation;
    *) crs3xx - improved system stability when creating many ACL rules on CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
    *) l2tp - improved system stability when processing L2TP control messages;
    *) lte - added MAC address and IPv6 LL address persistence after reboot on EG12 and EG18 modems;
    *) lte - made "no" the default value for "use-network-apn" parameter;
    *) ntp - allow adding duplicate server address if dynamic entry exists;
    *) ntp - fixed multicast mode support;
    *) ntp - improved IPv6 address support;
    *) ospf - fixed default route origination when "default-originate=if-installed" "redistribute" is enabled;
    *) ospf - fixed external LSA not updating after prefix netmask change;
    *) ppp - added "comment" option for PPPoE servers;
    *) ppp - improved stability when handling large amount of connections simultaneously;
    *) queue - improved system stability when using more than 255 unique packet marks;
    *) route - fixed ECMP load balancing in FastPath;
    *) route - fixed route addition to VRF from BGP;
    *) route-filters - renamed "*-set" to "*-list";
    *) sms - increased "at-chat" timeout when sending SMS;
    *) switch - fixed port-isolation misconfiguration detection when using multiple switches;
    *) switch - improved switch chip initialization process on bootup for CCR2004-16g-2s+ devices;
    *) ups - fixed UPS support;
    *) vxlan - fixed "group" and "interface" setting reset after upgrade (introduced in v7.2rc2);
    *) vxlan - fixed running state after reboot when using "interface" and "group" settings;
    *) wifiwave2 - added "client-isolation" feature;
    *) winbox - added "host-uniq" parameter to PPPoE client interface;
    *) winbox - do not show "Antenna Scan" button on devices that do not support it;
    *) wireguard - allow same peer's public key for different interfaces;
    *) wireguard - fixed IPv6 traffic processing with multiple peers;
    *) wireless - added "3gpp-info" parameter to interworking configuration;
    *) wireless - added EAP-AKA to interworking's realm configuration;
    *) wireless - correctly preserve WMM priority when receiving packets;
    *) wireless - improved nv2 link stability;

    Download the new 'RouterOS 7.2rc4' version here: https://mikrotik.com/download

  18. 7.1.3 changelog:

    *) bridge - fixed PPPoE packet forwarding when using "use-ip-firewall-for-pppoe" setting;
    *) bridge - fixed bridge filter and NAT rules on ARM64 and TILE devices;
    *) bridge - fixed filter and NAT "set-priority" action;
    *) conntrack - properly detect helper status;
    *) crs3xx - fixed watchdog timer functionality;
    *) ppp - improved stability when handling large amount of connections simultaneously;
    *) sms - increased "at-chat" timeout when sending SMS;
    *) switch - improved switch chip initialization process on bootup for CCR2004-16g-2s+ devices;
    *) vxlan - allow unsetting "group" and "interface" properties;
    *) vxlan - fixed running state after reboot when using "interface" and "group" settings;
    *) wireless - correctly preserve WMM priority when receiving packets;
    *) wireguard - fixed IPv6 traffic processing with multiple peers;

    Download the new 'RouterOS 7.1.3' version here: https://mikrotik.com/download

  19. 6.49.3 changelog:

    *) bridge - improved system stability when initialising bridge interface
    *) console - updated copyright notice;
    *) defconf - fixed secondary-frequency configuration;
    *) ethernet - improved system stability when receiving large packets on devices with 88F3720 CPU (nRAY, LHGG);
    *) led - fixed default LED configuration for CubeG-5ac60ad;
    *) netinstall - fixed x86 installation process;
    *) socks - fixed SOCKS5 support;
    *) upgrade - improved 404 error handling when checking for new versions;
    *) winbox - show "System/Health" only on boards that have health monitoring;
    *) wireless - added U-NII-2 support for US and Canada country profiles for OmniTik 5, Metal 52 ac, and GrooveA 52 devices;
    *) x86 - fixed downgrade from RouterOS v7.1.2 and above;

    Download the new 'RouterOS 6.49.3' version here: https://mikrotik.com/download